Just How to Remove as well as Replace a Bath Tub.
Just How to Remove as well as Replace a Bath Tub.
Blog Article
We've noticed the article involving How to Install a Bathtub: Install an Acrylic Tub and Tub Surround listed below on the net and felt it made sense to write about it with you here.
Mounting a bath tub isn't exactly rocket science, yet it does require strong plumbing, woodworking, and also in some cases, tiling skills. Replacing an old bath tub with a new one is additionally a moderately difficult job. If the old tub is conveniently accessible, the job can move speedily; if you have to open a wall to eliminate the old bathtub and also place the new tub, the job is a lot harder. In either instance, the project is within a home handyman's skills, although you will need a helper to leave the old bathtub and also embeded in the brand-new one. Make certain you have qualified yourself for the job as well as are comfortable attempting it. Rather than hiring a contractor to take over a halfway-completed task, it is far better to take into consideration utilizing one before you begin. Chances are you may require a specialist plumber to make tube connections.
This short article will aid you mount a brand-new tub in your restroom if you have actually already bought a brand-new bathtub as well as don't need to transform the plan of your previous water system pipes.
Your tools and also product list must make up the following:
Removing Old Touches
If you need to change old faucets with new ones as a part of your installation, after that the first thing you ought to do is disconnect the water. After doing so, switch on the taps to drain pipes any type of water remaining in the system. The procedure of eliminating the existing taps can be fairly troublesome due to the restricted access that is commonly the situation.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the taps. Have a towel prepared for the continuing to be water that will certainly come from the pipelines. Once the supply pipelines have been gotten rid of, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming during this procedure. Once the faucets have been eliminated, the holes in the bath/basin will need to be cleaned of any type of old sealing substance.
Before carrying on to fit the brand-new taps, compare the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic port to stop damage to the string. One end of the connector fits on the plastic tail of the tap and also the other end supplies a connection to the existing supply pipelines.
If you need to fit a monobloc, after that you will certainly require minimizing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, place the tap in the installing opening in the bath/basin ensuring that the washing machines are in place between the faucet and the sink. Secure the faucet in position with the manufacturer supplied backnut. As soon as the tap is safely in position, the supply pipelines can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with regular tap connectors. The former kind ought to be linked to the tap finishes initially, tightening up only by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Installing the Bath tub
Using both wood boards under its feet, position the bath tub in the needed setting. The wooden boards are valuable in evenly spreading out the weight of the bath tub over the area of the boards instead of focusing all the weight onto four little factors.
The following goal is to ensure that the tub is leveled all round. This can be accomplished by inspecting the spirit level as well as changing the feet on the bath tub until the spirit level reviews degree.
To set up taps, fit the bottom of the outermost versatile tap port to the suitable supply pipeline by making a compression join; after that do the same for the other faucet.
Turn on the water and also check all joints and also brand-new pipework for leakages as well as tighten them if necessary. Fill up the tub as well as additionally examine the overflow outlet and the normal outlet for leakages.
Ultimately, deal with the bath paneling as explained in the manufacturer's instruction manual. Tiling as well as securing around the bath tub should wait until the bathtub has actually been used at least when as this will resolve it into its last placement.
Preparing for the Setup
First of all, the supporting frame provided with the bathroom needs to be fitted (if needed) according to the maker's instructions. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is important to make certain that if the faucet features a plastic washer, it is fitted in between the bath and the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the faucets device to stop stress on the bath tub.
Fit the flexible tap adapters to the bottom of the two faucets utilizing 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet via the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. See to it you utilize all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath need to now prepare to be fitted in its last setting.
Tiling Around the Bathtub
In the location where the bath satisfies the tile, it is needed to seal the accompanies a silicone rubber caulking. This is important as the installation can move sufficient to crack a stiff seal, causing the water to permeate the wall surface between the bathroom and the tiling, bring about problems with wetness and feasible leaks to the ceiling below.
You can pick from a variety of coloured sealers to blend in your fixtures and also fittings. They are offered in tubes and also cartridges, and can sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger void to fill, you can fill it with spins of soaked newspaper or soft rope. Remember to always load the bathtub with water before securing, to allow for the motion experienced when the bathtub remains in use. The sealant can fracture fairly early if you do not think about this movement before securing.
Alternatively, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily offered on the marketplace. It is suggested to fit the tiles utilizing waterproof or water-proof glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am very fascinated with Tools You Need to Install a New Bathtub and I'm hoping you liked the new piece. Those who enjoyed our blog entry please make sure you remember to pass it around. I praise you for your time. Come back soon.
Visit Our Site Report this page